Inshore: The Basics Of Anchoring - The Fisherman

Inshore: The Basics Of Anchoring

When deploying the anchor, make sure your legs and feet are clear of the line.

An anchor can be a valuable fishing tool. Know how to deploy one when needed.

Safe anchoring for the small-boat owner, a vessel-class perhaps defined as 25 feet in length or less, is one of the most important keys to nautical safety and successful fishing for the new boater. Here are the basics you need to know.

All anchoring gear attached between the anchor and the boat is collectively called the “rode.” The rode includes chain, line, and hardware. Nautical terminology dictates that the main length of anchor rode is called “line” not “rope.” Although many types of rope exist—synthetics like Dacron, nylon, polypropylene, polyester, and polyethylene, or natural fiber like manila—the best material for anchor line is nylon. Rope experts recommend 100% braided nylon for this use. It’s strong, flexible, doesn’t rot, resists sun decay, and most important, it stretches by 15 to 30 percent, which cushions your ride at anchor in rough conditions. Nylon also sinks because it can absorb up to 6% of its weight in water, which makes it better for holding anchor than other lines like polypropylene, which float.

Attach your nylon line to at least 6 feet of medium (1/4- or 5/16-inch diameter) galvanized chain. This serves three purposes; first, it prevents line chaff over rough structure; second, its weight lowers the angle of pull, which sets the anchor better; and third, the slack or belly created from its weight helps offset surges from waves and wakes. Connect the line to the chain using an eye splice around a thimble shackled to the chain (or buy anchor line pre-rigged).

An anchor does not hold you in place by its weight; it requires proper scope. Scope is the ratio of the diagonal length of the anchor line to the vertical height from the bottom to the top of the bow. You must also calculate the height or amplitude of a rising tide. Without sufficient anchor line angle (scope) the best anchor and chain still won’t hold your vessel in place. A minimum of a 5:1 ratio of length to depth is required for average fishing conditions.

However, for heavy conditions such as a strong wind and tide pushing against a vessel with a dead motor, you’ll need a 10:1 ratio for safety. For maximum effectiveness, all anchors require a low angle of pull, preferably less than 8 degrees. A short scope reduces holding power because the angle of pull is too high, which breaks the anchor out of the bottom.

Bottom composition is important for firm anchoring. Mixtures of mud and clay or sandy mud make excellent holding for most anchors. Firm sand is good, too, if your anchor will bite deep into it with sufficient scope. If possible, avoid loose sand, soft mud, stones, and weed bottoms. Bottom characteristics are denoted on charts.

The two most common anchor types are the Danforth or “fluke” and the plow or “scoop,” with the Danforth the best bet for smaller bay boats. But the plow anchor generally performs better overall in grass, mud, and sand.

To set an anchor, lower—not throw—it overboard to the bottom and then back down (reverse) while the line is paid out—making sure you or your assistant doesn’t get a coil wrapped around an arm or foot. When you believe sufficient scope is paid out (marking your anchor line in 25-foot increments helps determine line out), quickly snub the line around a bow cleat. A Danforth can be initially set with a scope as short as 2:1 or 3:1 on an ideal bottom.

After the anchor catches bottom, pay out more rode for the expected conditions, preferably of at least 5:1. The scope must be sufficient for holding, but in a crowded fishing spot you must also consider not encroaching on fellow anglers. Then make your anchor line fast by running it through a bow chock and cinch it to a cleat. To tie to a cleat properly, take a full turn around the base, then one turn around each horn, crossing diagonally over the center of the cleat. Finish with a half hitch around one horn. Never use a clove hitch because it may seize and jam. Last, turn off the idling engine.

If your anchor drags, the best option is to pay out more scope until it sets. When you’re done fishing and ready to weigh anchor and move, start your motor first (to be sure it starts), then slowly run up the anchor line while taking in slack. The anchor should break free when the line becomes vertical; if not, continue past it. Be sure the anchor doesn’t strike your propeller or hull at the end of the haul out.



Inshore: Striper Jigging 101

The basics of jigging for striped bass in the Northeast.


Inshore: The Thrill Of The Hunt

There is nothing like the satisfaction of hunting and finding your own fish.

Ikejime spike

Inshore: Harvest Humanely

Between being more humane and creating a better table fare, Ikejime is the way to go.